Tel: +44 (0) 207 629 6606 | Email: [email protected]

Search


Pendulum of Mayfair - Antique Clocks

King House,
51 Maddox Street,
London W1S 2PH

Telephone: +44 (0) 207 629 6606

Fax: +44 (0) 207 629 6616

Email: [email protected]

Coppelia Antiques - Clocks & Furniture

Holford Lodge,
Plumley Moor Road,
Plumley,
Cheshire
WA16 9RS

Telephone: +44 (0) 1565 722197

Fax: +44 (0) 1565 722744

whos who
Pendulum of Mayfair on Facebook
Pendulum of Mayfair on Twitter
Pendulum of Mayfair on linkedIn
Pendulum of Mayfair on YouTube
Pendulum of Mayfair RSS Feed
Pendulum of Mayfair Google+

Setting up your 'Antique Grandfather / Longcase & Bracket Clock' at home

CARE & SETTING UP INSTRUCTIONS OF A LONGCASE CLOCK

Congratulations on your purchase of a Longcase clock from Pendulum of Mayfair Ltd / Coppelia Antiques. Given proper care and conditions your Longcase clock should give many years reliable service.

Proper Care After Set-up

1) Winding:

‘30Hr’clocks are generally wound with a rope or chain. This should be done once per day.  

‘8 Day’ clocks may either have one weight (typically regulator clocks) or two/three weights. All weights are to be wound by inserting the correct size of key on to the winding arbour. Your clock should arrive unwound, so on winding, the lines should follow the grooves in the barrel (if applicable) ‘8-day’ clocks are usually wound clockwise

‘Month’ duration clocks typically as above but since these clocks have an extra wheel in the train they are generally wound anti-clockwise.

2) Time:

When setting the time never move the hands backwards. If you move the clock hands backwards past a striking section you may cause damage to the movement. Always let the clock strike each hour/quarter etc when setting the time. It is also a good idea to wind the clock prior to setting the time and starting the clock.

3) Calendar:

As the clocks allow for 31 days per month, when there is less than 31 days, you need to adjust the calendar. Depending on the sort of calendar of your clock, this can be done from the front (hand variety) or the rear (square or lunette variety). The calendar disc on the latter sort is attached to the back of the dial. You can move the square or lunette type from the front but you may leave finger prints to the dial, that will leave a mark over time. If the calendar does not want to move, wait for a few hours and try again, it may be in mesh. Generally the calendar can be moved by hand between 3 and 5pm each day.

4) Regulation:

If you notice a day after set-up the clock is running fast by a few minutes, the only thing that controls the timekeeping is the pendulum. (assuming the minute hand is not loose) Stop the clock by grabbing the pendulum and move the nut on bottom of the pendulum anti-clockwise, in effect lengthening the pendulum. Generally 1 turn either way would make the clock gain/lose 1 minute per day. Up= Faster, Down = Slower.

 

5) Striking:

If your clock is count wheel strike, occasionally the clocks strike may go out of sequence. This can happen if the clock has been left to run out. There is a lever on the movement which you can lift to adjust this. Alternatively if the clock is striking 4 but pointing to three and the time is 3.10 by the clock, move the clock hands past four quickly and on to five before the clock has finished striking five. The clock will now be in sequence again, striking five and pointing to five.

HUMIDITY

You should always keep your antique clock in R.H. 40-65%. Never keep your clock in dry or damp conditions. As a result of central heating over the last 20 years more damage has been done to antiques than at any time in the previous 300 years. Always check your humidity level. It is recommended in dry conditions you purchase a Humidifier or in damp conditions you purchase a DE-Humidifier.

WAXING

Always use a Beeswax polish every few years, never use spray polishes on antiques.

OILING

You should oil your clock movement every year or so with a specialist clock oil. This can be applied with an artists brush. Oil needs to be applied to the pivot holes on the front plate and backplate. (I.e. where the pinions of the wheels go through front and backplate) It is also advisable to oil the pallets and the pulleys that the weights hang on. You do not need to oil any of the gears in the movement. A few drops of oil should oil an entire movement, do not over oil as this will attract dust and cause wear.

SETTING UP YOUR LONGCASE CLOCK ON DELIVERY

Parts of a Longcase Clock:

1) Trunk

2) Hood

3) One / Two / or Three Weights

4) Pendulum

5) Movement

Tools Required to install your Longcase Clock and Fix it to a Wall

1) Drill

2)Wood baton (8inch * 2inch * thickness of skirting (generally 1inch thick)

3) Screwdriver and screw to screw clock into baton

4) 4/5 thin wooden packing blocks to straighten clock and make it lean against the wall

5) Raw plug and screw to fix baton to wall

Introduction

It is always advisable to fix your antique clock to the wall. If this is not done then apart from the risk of the clock being knocked over, sometimes if the clock is not firm the clock may stop when the weights are level with the pendulum, as the clock rocks slightly. You can avoid the fixing to the wall by just packing up the front feet up and thus throwing the clocks weight to the wall, which is done when you screw the clock to the wall in any case, but I would recommend fixing. The process outlined below appears very difficult but it is easily carried out by most people. If you do not wish to undertake this process, you can ask any joiner to do this for you. Let them have our instructions if they are unsure of the process.

 

The first step after unpacking the boxes that the clock is packed in, is to check the clock for any damage in transport and if so , inform your shipper. Hopefully this is not the case and you can continue with the fixing of your clock. Find the most suitable place you would like the clock to be and with the use of the thin packing blocks under the clocks front feet, place the trunk of the clock against the wall in this position.

 

The second step requires some assistance from a willing family member. Now you have set the trunk straight against the wall, (by eye is fine) whilst one person takes the movement and places it on the cheeks of the case, the other person brings the pendulum. Do not leave the movement unattended on the cheeks, keep your hand holding the clock until at least the pendulum is connected. Now thread the pendulum up though the crutch (the slot to the rear of the movement) and finally onto the back-cock of the movement.

Generally it is now safe, if the movement is far back on the cheeks, to let go of the movement now, but do so carefully, making sure the movement does not overbalance.

 

At this stage put the hood onto the trunk and with your hands under the bottom of the seatboard lever the movement into the correct position in the mask, making sure the hood is still firmly back. The dial now should be fitting the mask evenly on both sides. At this stage you can carefully take the hood off and if applicable screw the movement down into the cheeks and so it it stable and in the correct position. This is an optional stage of the process.

 

Now comes the time for fixing the clock to the wall or if you do not wish to do this, all you need to do is hang the weights on the clock and follow the latter stages of the process.

 

Mark the wall through an existing central hole in the clocks backboard (if there is one about chest height as you open the trunk door) If not drill a small hole through the clocks backboard at this point and mark. Temporarily at this height and to one side of the clock put the baton you are going to use just behind the clock, leave it there sticking out from one side of the clock for the moment while you check the pendulum is free and not touching the backboard. You have now checked the baton is of the correct thickness. If the pendulum is still touching the back of the clock while the baton is temporarily behind the clock and the movement is correct in the mask. (not been pushed back) use a slightly thicker baton and recheck.

 

Now you are happy with the thickness of the baton, mark the position of where the clock is standing and move the clock to one side. (two people can lift the complete clock to one side or alternatively dismantle in the reverse order you set up. Make sure you know exactly where the clock was positioned. To one side of the mark you have on the wall, make sure you now test the wall so that there is no problem with drilling here. (no cables etc behind) Drill the hole to one side of the mark you have made to the correct length of your raw plug. Attach raw plug and screw baton to wall. Re-assemble clock in exactly the original place with exactly the correct number of packing pieces under the front feet. Screw through the hole in the clock’s backboard into the wood baton now fixed to the wall. Your clock is now secure.

 

You can now attach the clock weights and wind the clock. The clock should come to you unwound so on winding the lines should follow the grooves in the barrel (if present)

 

Now you can swing the pendulum and listen to the tick. The clock should tick evenly, I.e. tick, tock. Not tick, tooooooock. If the clock is straight and you are happy with this you need to adjust the beat. You will need to bend the crutch away from the sound of the long tock. If the clock is not in beat even if all the hands of the clock are free and not touching the dial or each other, the clock will stop within a few minutes. If the clock is in beat though and the clock stops at five past one for instance the hands may be touching, gently ease them away from each other.

Now your clock is set-up you can now sit back and relax.

If you want to set the clock up in a corner position, it is basically the same process as above but you will need a i-shaped backed. The baton will be on the wall and you will have a baton on the back of the clock with a adjoining piece of wood connecting the two. The above process may seem complicated but it really is not and should take no more than 20 minutes for a practical person or 45/50 minutes for fitting in a corner.

SET-UP SUMMARY SHEET

1) Decide where you want clock and fit a wooden baton to wall, similar thickness to skirting.

2) Place case in front of this and fix it to the piece of wood.

3) Place movement in case and get someone else to hang pendulum on whilst you steady movement.

4) Put the hood on and then slide you hand under seatboard to position in the dial in the mask correctly

5) Remove hood and attach weights correctly to pulleys.

6) Carefully wind up clock making sure the lines are not twisted and winding evenly on barrels

7) Wind the clock to a point where the lines fill the barrel, do not over wind. Leave a gap of about 2inch between the underneath of the seatboard and the pulley.

8) Swing the pendulum gently and listen to see if the clock is in beat. Tick - Tock. If the sound is correct, set-up is complete, if not adjust beat of clock by bending crutch away from the sound of the long tock.

9) If the timekeeping is fast, adjust by lowering pendulum rating nut on bottom of pendulum. Roughly one turn down will make the clock go slower by one minute per day and vice versa

10) Always wind the weights before moving the hands of the clock.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Recent Articles

This section is currently under construction, please try back later